Type 140 Power Feed

Products > Power Feeds > Type 140 Power Feed >

Type 140 Power Feed

Type 140 - Knee, Table, and Cross Feeds

Semi-automated machining on Class 1 mills to 3 hp.
Peak Torque (half-wave series motor): to 140 in.- lb. / 15.8 NM torque
Intermittent Torque: 105 in.- lb. / 11.9 NM
Continuous Torque: 90 in.- lb. / 10.2 NM
Variable Feed Rate:
.75-25 IPM / 19-635 mm/min (table & cross)
.5-12 IPM / 13-305 mm/min (knee)
Rapid Traverse:
35 IPM / 889 mm/min (table & cross)
12 IPM / 305 mm/min (knee)
Gear Reduction Ratio (motor to screw shaft): 72:1.
Helical gearing and torque limiting friction safety clutch with new and improved gear.
Electrical: 110V, 50/60 Hz, 2.5A.
Approx. weight: 15 lb. / 6.8 kg.

Installation instructions and drawings

NOTE: Servo Products Company has made every effort to provide mounting hardware kits that are as accurate and complete as possible for each machine model. However, machine builders may change their designs without letting us know. Therefore, some kits may not fit properly. Please let us know when this happens. The following Documents are Adobe Acrobat PDF files. Click here for a free copy of Acrobat Reader.

Knee Feeds Note - Various mills such as the Bridgeport Series II, Lagun FTV3 and Deluxe, Alliant RT4V and other large mills are too heavy to lift with a Type 140. The Type 150 can not be used as a knee feed since it will stall under load. Use a Type 350X or a Type 200 for heavy knees. To replace a knee feed when you don't need the mounting hardware, use the ECF-350X, ECF-140KNEE or ECF-200KNEE.

Hold down the “Shift” Key to open the documents in a new browser window.

Machine

Table Feed

Cross Feed

Knee Feed

Base Feed - No mounting hardware included

ECF-140

ECF-140

ECF-140KNEE

GENERAL PURPOSE
(If your mill model is not listed below, you can use this. Also use this for custom machine applications.)

ACER 3VS 3VK

ACER after 1992

ACRA MILL 9 x 42

ACRA MILL 9 x 49

ACRA MILL 10 x 50

ACRA MILL 10 x 54

ALLIANT

ALLIANT RT2-50

ATRUMP

BIRMINGHAM 942, 1050

BRIDGEPORT SERIES I (hand fed mill) If you're not sure, see this.

BRIDGEPORT (replaces electronic feed) For description, see this. If you need information on this model for S/N 564146 or older, see this.

BRIDGEPORT (replaces gear box feed) For description, see this.

BRIDGEPORT 12" CROSS TRAVEL

BRIDGEPORT 9" CROSS TRAVEL

BRIDGEPORT SERIES II

see Type 200/350X

BRIDGEPORT SERIES II SPECIAL

see Type 200/350X

BRIDGEPORT (After Aug 2010)

BRUTE 9 x 42, 9 x 49

BRUTE 10 x 50

CHEVALIER, LARGE & SMALL

CLAUSING ATLAS / KALAMAZOO

CLAUSING KONDIA

CLAUSING KONDIA FV-300

see Type 150

see Type 150

CLAUSING 400EVS, 450EVS, 500EVS

COMET INCH (.625 dia lead screw)

COMET METRIC (.630 dia lead screw)

COMET 9 x 42, 3VHG, 2SHG

COMET 10 x 50 3KV

COMET 10 x 50 3KVHD, 3KVHD-B,

COMET 10 x 54 4KVHD

COMET 10 x 50 5KVHD

CONCORD

DO ALL

EDELSTALL F10V, 401

EDISON

ENCO 100-1527, 9 x 42

ENCO 100-1588, 10 x 54

ENCO 231

ENCO 249

see Type 150

ENTERPRISE

EXACTO

EX-CELL-O 602 (no coolant trough)

EX-CELL-O 602 (w/coolant trough)

FIRST YAMAZEN

HARTFORD

HOLKE MACHINIST

HOLKE S/N 5172 UP

HURCO SM1

HURCO SM2

see Type 150

see Type 150

INDEX 45, 645, 745

INDEX 747, 847, 860, 887

JET 1048 VS

JET Y

JOHNFORD MV54

KENT 2S

KENT 3VK, 4VK, 5VK

KENT 5KV

KINGSTON KTM 3V

KONDIA G & FV1

KONDIA 2

see Type 150

see Type 150

LAGUN

LAGUN FTV3

see Type 150

see Type 200/350X

MARENA 942

MARENA 10

MAXMILL

MICROCUT

MILLPORT 2S, 3V, 3VH

MILLPORT K MILL

MILLPORT 10 x 50

NEWPORT

SELECT 1VB (.630 dia lead screw)

SELECT 1VB (.625 dia lead screw)

SELECT 1VBVS

SERVO SV50

SERVO SV54

see Type 200/350X

SHARP FIRST, LMV, LCS

SHARP HMV, OMV, QMV1, QMV2, TMV

M-4380-140

SHARP 1-1/2 YC

SHARP VIA

SIBER HEGNER RB1

SOUTH BEND IMPORT

SOUTH BEND 2 HP

SOUTH BEND 3 HP

SOUTH BEND / SE+5-DIGIT SER. #

SOUTHWESTERN TRAK TRM

SUPERMAX 1-1/2 , 16KV

SUPERMAX 16VA

TOPWELL

VICTOR VSK or VK

VICTOR, 16 VSK or VK

VICTOR, 380 VSK or VK

WEBB

WEBB CHAMP

see type 150

WEBB CHAMP 1-1/2 (before Jan '91)

WEBB CHAMP 1-1/2 (after Jan '91)

WELLS INDEX 747, 847, 860, 889

see Type 150

see Index

WELLS INDEX 837

WILLIS MICRO CUT